123 TRUCK DIAGNOSTICS(855) 450-1212 · Mobile diagnostics 24/7
Home › Fault codes

Truck fault code lookup: SPN and FMI in plain English

Type the SPN and FMI from your dash. You get what it means, the usual causes, what to check first and whether to keep driving.

Call (855) 450-1212Request diagnostics
Look up a code

Common codes we get calls about

SPNWhat it isSystem
27EGR valve positionEGR
91Accelerator pedal positionControls
94Fuel delivery pressureFuel
97Water in fuel indicatorFuel
100Engine oil pressureEngine
102Intake manifold (boost) pressureAir
105Intake manifold temperatureAir
110Engine coolant temperatureCooling
111Coolant levelCooling
157Fuel rail pressureFuel
168Battery voltageElectrical
190Engine speedEngine
412EGR temperatureEGR
641VGT actuatorAir
1569Engine protection torque derateDerate
1761DEF tank levelAftertreatment
3031DEF tank temperatureAftertreatment
3216Aftertreatment intake NOxAftertreatment
3226Aftertreatment outlet NOxAftertreatment
3251DPF differential pressureAftertreatment
3361DEF dosing unit (doser)Aftertreatment
3364DEF qualityAftertreatment
3719DPF soot loadAftertreatment
4334DEF pressureAftertreatment
4364SCR conversion efficiencyAftertreatment
5246SCR operator inducementDerate

FMI: how it failed

FMIMeaningWhat it usually points to
0High, most severeThe value is above the normal range at the most severe level.
1Low, most severeThe value is below the normal range at the most severe level.
2Erratic, intermittent or incorrectThe signal is jumping around or does not make sense.
3Voltage above normal or shorted highUsually an open ground or a short to power in the circuit.
4Voltage below normal or shorted lowUsually a short to ground or a missing supply voltage.
5Current below normal or open circuitOften a broken wire, a loose connector or a failed component.
6Current above normal or grounded circuitOften a short to ground or a failed component drawing too much current.
7Mechanical system not respondingThe controller commanded something and it did not move or respond as expected.
8Abnormal frequency, pulse width or periodThe signal timing is wrong.
9Abnormal update rateThe data is not arriving on time over the network.
10Abnormal rate of changeThe value changed faster than physically possible.
11Root cause not knownA failure that does not fit the other categories.
12Bad intelligent device or componentA module or smart sensor reports an internal fault.
13Out of calibrationThe component needs calibration or a learn procedure.
14Special instructionsManufacturer-specific; check the OEM troubleshooting for this code.
15High, least severeSlightly above normal.
16High, moderately severeModerately above normal.
17Low, least severeSlightly below normal.
18Low, moderately severeModerately below normal.
19Received network data in errorAnother module is sending bad data.
31Condition existsThe monitored condition is present.

Codes follow the SAE J1939 standard used by heavy-duty engines and transmissions. Manufacturers add their own codes and test steps, so this is a starting point for a conversation with a mechanic, not a replacement for one.

Questions people ask us

What do SPN and FMI mean?

SPN (Suspect Parameter Number) identifies the part or system the controller is reporting on. FMI (Failure Mode Identifier) says how it failed, for example voltage too high, open circuit or value too low. Together they point the mechanic to where to test.

Can I just clear the code?

Clearing a code without fixing the cause usually brings it back, sometimes as a derate at a worse time. Clear it after the repair, then confirm it stays clear.

Are codes the same on every engine?

Standard SPN and FMI numbers are shared across manufacturers using the J1939 standard, but each manufacturer also has its own proprietary codes and troubleshooting steps.

123 Truck Repair is a service of MTS Mobile Truck Repair Service LLC, dispatching mobile mechanics, heavy-duty shops and wreckers across the United States and Canada, 24/7. · (855) 450-1212 · Request a quote · Local numbers · Real calls · mtstruckservice.com

Engine and truck brand names are used only to describe what we diagnose. We are an independent service, not affiliated with any manufacturer.

Call (855) 450-1212Request